How to make a toy crossbow at home. How to make a powerful crossbow at home

A copy of an ancient crossbow is a very interesting thing, both in terms of appearance, and when shooting from it. Now let's talk about how to make a crossbow at home so that it really looks like ancient weapons. Nowadays there are many modern crossbows, but their cost is quite high, and I want to hang on the wall in the bedroom exactly the current copy of the ancient crossbow.

Now let's take a step-by-step look at what is needed to create a wooden crossbow. Few tools are needed.

1. Well sharpened knife.
2. Drill.
3. Hacksaw for metal.

Material preparation, or How to make a crossbow out of wood

To make the product look and shoot like a real weapon, you need to make it from suitable wood:

1. poplars.
2. Ash.
3. Pines.
4. Oak.
5. Maple.
6. Acacias.

These trees are perfect.

The crossbow consists of two main parts - the bow and the stock. If we make weapons with a capacity of up to 20 kilograms, for a bow you need to find an even branch five centimeters thick and a meter long. If the power of the crossbow is planned to be more than 20 kilograms, then it is better to take a blank 10 centimeters thick and a meter long. For the crossbow bed, select a branch with a diameter slightly thicker than the blank for the bow. If there are branches on the sawn material, in no case should they be completely cut off. You just need to shorten them so that the length is from three to five centimeters. If you cut off the knots completely, they will immediately crack, and the workpiece will be spoiled.

Drying of harvested wood

Before you make a crossbow with your own hands, you need to ensure that the material dries gradually. To do this, you need to cover the saw cuts with varnish so that moisture does not come out through them too quickly. Slices on knots are also covered. If this is not done, then due to rapid evaporation, the tree will crack, and this is undesirable. After that, the blanks should lie for a month in a dry and dark place. The longer the tree dries, the better.

Primary processing

The material is ready, we can proceed. Let's start with the bow. We examine the annual rings of the tree. Where they are thinner, the north side, that's what we need. In this place, the structure of the material is much denser. Now you need to cut the workpiece in half and take the north side for the product. After everything is done, the tree must be allowed to lie down for another week so that the remaining moisture comes out.

Making a crossbow bow

We start making a bow, during which we will see the structure of the tree and learn how to make a crossbow at home using ancient technologies. So, let's get started, you need to cut the layers of the tree, where its core is present. If you leave it, then there is a risk that longitudinal cracks will go. After we measure the middle of the onion and begin to cut off the excess material, making the onion. When processing, it is necessary to ensure that his shoulders are the same. We check for bending all the time. As soon as the shoulders begin to bend even a little, you need to make a trial bowstring.

A trial bowstring is a strong rope, on which there is one loop on one side, and several, located at different distances, on the other. They are needed in order to measure the bend of the bow limbs. The more material is cut off, the more they can be bent, while changing the loops to the nearest ones. By pulling the test string constantly, it is easy to track whether the bow is even after processing the bow. After all, if you look only visually, you can make a big mistake. The density of the tree is not the same in all places, so a seemingly perfect bow can bend unevenly. Sometimes it happens that a thick section is a weak point, and a thinner one, on the contrary, does not bend. In order not to make a mistake, you need to constantly check the bow. Only by studying all the nuances, you can make a working copy, understand how to make a crossbow with your own hands, and fully display the power and beauty of the ancient weapon.

Making a crossbow stock

In front of the bed, you need to cut a two-centimeter recess where the bow will be located. After we mark 30 cm from the edge, a bowstring and an arrow will walk on this surface. We level this plane if it has bends or branches. After you need to measure the place for the gutter 1 cm thick and 0.5 cm deep, then cut out the holes for the bow and the trigger. It is better to do this with a chisel or a carpenter's cutter, and in order to understand in detail how to make a crossbow, drawings to help.

Trigger mechanism

Take the simplest hold, called a nut. It is a cylinder that rotates freely on an axle. On the one hand, its hooks for the bowstring, on the other - an emphasis for the L-shaped trigger. If the crossbow is up to 30 kg of tightness, the descent can be wooden. However, if the power is greater, it should be made of metal.

Making a bowstring

You need to take a board and insert pegs 1 cm thick. They should protrude 3 cm. The field of which, from one to the other, we wind a nylon thread in a circle. When the thickness of all the threads is about 5 mm, it is necessary, without removing from the pegs, to wrap this skein around once in a circle so that all the threads are tightly wrapped. After that, near the peg, we collect two halves of the bowstring with our fingers and wrap it again, but already much denser, until the next peg. So, we get a bowstring with two loops. A diagram of how to make a crossbow will help you understand everything. Everything about her is very clear.

We collect the crossbow and pull the bowstring

First you need to attach a bow to the stock, then we mount the trigger mechanism, after that we pull the bowstring. You can’t just pull it, so you need to use the trial. Next, you need to pull the crossbow. When the bow is bent, we hang the bowstring. After that, the test is removed. Everything, the ancient weapon is ready. Here's how to make a crossbow at home using only the simplest tools.

Making a toy mini crossbow

For fun at home with the kids or for fooling around with friends, you can make a mini crossbow from improvised materials. What is needed for this:

1. Two wooden skewers.
2. Carpenter's cutter or knife.
3. Scotch.
4. Wooden clothespin.
5. Bead.

Scheme, or How to make a mini crossbow from what can be easily found at home

1. We take wooden skewers and cut off the sharp ends from them. After that, we tie them together at the edges. This will be the crossbow bow.
2. We take a bead, mark two segments on it, equal to the length of the bow of our miniature weapon. After we cut off these two parts and connect them together with adhesive tape. This is the stock of a crossbow. Tape the bow on the front.
3. After that, we pull the bowstring on the crossbow.
4. We delay it and look at what distance to set the hook. They will serve as a clothespin, or rather, its spring and one half of the wooden part.
5. On the bed of the crossbow we cut out the necessary grooves so that it becomes instead of the missing part of the clothespin. We collect our hook.
6. The crossbow is ready, we press the clothespin from above, thereby unclenching it, we pull the bowstring along with the arrow and clamp it. To shoot again, press the top.

We figured out how to make a mini crossbow, and now we can go ahead and create weapons from pencils.

Create a crossbow from pencils

For this you need to take:

1. Four pencils.
2. Seven rubber bands
3. Ballpoint pen case.
4. Scotch.

Shall we start?

1. First you need to take the pencils and connect them two by two together. You can use rubber bands or tape. This will be the bow and crossbow bed.
2. In front of the bed, we wind the bow from below.
3. From above on the bed we tape the body from the handle with tape, this will be the guide for the arrow. It can be made from the core of the same pen.
4. Now we put one elastic band on the ends of the bow, and we tie their edges with threads or tape to make a single bowstring. Now we grab the bowstring with the enclosed arrow, run it into the guide from the handle body and release it.

Here's how to make a pencil crossbow that shoots great.

Let's start creating a paper crossbow

This requires:

1. A4 sheets - 9 pieces.
2. Popsicle sticks - 4 pieces.
3. Scotch.
4. Durable nylon thread.

How to make a crossbow out of paper that will shoot pencils?

1. We put three sheets of paper in front of us lengthwise. We bend from left to right. Cut in half along the fold line. It turns out six sheets, the width of which is 10.5 cm and the length is 29.7 cm. We divide them into two piles of three sheets.
2. Using a pencil, we twist one, and then the second stack of sheets into tubes. Their length should be 10.5 cm, and the diameter should be slightly thicker than a pencil. So that they do not unwind, we fasten with tape.
3. We insert into one end of the tubes a popsicle stick a third of their length. We break off the protruding part. On the free side, we insert a whole stick of popsicle also by a third. These are the shoulders of the bow. Now you need to bend them in the center of the paper tubes in half.
4. We take five more sheets of paper, twist them with a pencil, this will be the bed of the crossbow.
5. We wind the shoulders of the bow to the resulting tube in front. It is necessary to evenly wind them in front of the bed of the product. Here's how to make a crossbow at home out of paper. Now he needs a hold, a trigger and a guide.
6. We tie the thread to the shoulders of the bow and pull it to understand where the hook will be. Having decided, we cut through the bed in this place. After that, we cut off a piece of the stick 3-4 cm in size and insert it into the hole so that it protrudes 5 mm from above and is a trigger from below.
7. And the final touch. We make a tube 3 cm long so that a pencil can freely pass into it, and we fasten it with tape in front of the crossbow above its bow. This is a stele guide. That's it, now you can pull the string, put, for example, a pencil into the guide and shoot.

Here we looked at the creation of a copy of an ancient crossbow. However, it was also interesting to create throwing weapons from improvised materials, as they say: on the knees. From paper, they even showed how to make a crossbow out of pencils, and a mini-weapon that turned out to be quite powerful for its size. So it’s worth looking at the world more broadly and always improvising, only in this way you can achieve excellent results in deeds worthy of admiration by people around you.

Make a crossbow with my own hands, You will not regret!

Evgenia Smirnova

To send light into the depths of the human heart - this is the purpose of the artist

Content

How to make a crossbow - this question worries both hunters and shooters. Shooting from a crossbow, as from military weapons left far behind. Today, crossbow shooting is mainly practiced professional athletes, as well as amateurs who want to shoot at targets. Crossbow shooting has a number of advantages over shooting firearms. Firstly, it is the noiselessness of shooting, and secondly, the availability and comparative safety. The crossbow does not require any permission and a medical examination to purchase it. It is enough just to buy a ready-made one (for which you will have to pay from several hundred dollars and more), or you can make a weapon yourself. That is why your favorite site useful tips the site will tell you today about how to make a crossbow yourself.

How to make a mini crossbow - instructions

Before you start making a crossbow at home, you should familiarize yourself with the structure of this weapon. It consists of several main parts: a wooden base, called a bed, a bow with a bowstring, as well as a sight and stirrup.

Types of weapons and ammunition

Experts distinguish between two types of crossbows - field and match. Feathered arrows are considered ammunition for both types. On sale there are carbon and duralumin feathered arrows. You can learn and compete in shooting with the help of a standard five-color archery target, which is also on sale. Shooters from field crossbows usually compete at distances of 35, 50, 65 meters (in the air) and at 10, 18 meters (indoors). Shooters from match analogues usually compete only in special rooms - shooting ranges at distances of 10 and 30 meters.

Hunting with a crossbow is an activity for real men

Many owners use their devices for hunting. Hunting with a crossbow is fundamentally different from hunting with a gun - not everyone likes to shoot animals from a tower, a helicopter or drive an animal in a large crowd. Hunting, on the contrary, loves silence and solitude. In some ways, this type of hunting resembles the well-known heroic fun - walking on a bear with a horn. In fact, for a shot, you need to get closer to the beast at a distance of 50 meters and closer. Not everyone will be able to approach a boar at such a short distance, and approaching it at such a short distance requires special hunting skills. Well, the more valuable the prey!

How to choose

All devices for hunting can be divided into two categories - block and recursive (classic). Recurve ones do not have the increased power of block crossbows, but they are much easier to use and are more reliable. The force of their tension is approximately equal to 50 kg. From recursive, they hunt birds, small and large animals. For hunting large and dangerous animals, more powerful block models are used. It is almost useless to shoot from them at a flying target - it is almost impossible to hit.

Power

For hunting a bird or a small animal, a crossbow with a pulling power of 50 kg is enough. With a tension power of 50-70 kg, you can hunt a large ungulate animal. For hunting wild boar, crossbows with a capacity of 80 kg are used.

What ammo can be used

Hunting large game requires special ammunition. You need to hunt large prey with the help of special professional arrows made of fiberglass or carbon. These arrows have sufficient strength and lightness, they are correctly centered, which guarantees a successful hit. On sale there are also sometimes excellent arrows made of aluminum. But such ammunition is suitable for hunting only small animals or birds. Arrow manufacturers provide for the possibility of turning hunting ammunition into sports ammunition - for this you just need to change the arrowhead. The threaded connection allows you to do this very quickly. A hunting arrow weighs from 30 to 35 grams, the length of such an arrow is from 45 to 50 cm. As a rule, the length of the plumage of a hunting arrow is greater than that of a sports arrow, because the arrow needs to stabilize faster in flight to assume a combat position.

For fishing

Some shooters use a crossbow not only for hunting, but also for fishing. For fishing with a crossbow, harpoon arrows of a special needle shape are used, which allow the arrow to move in the water. At the end of the fishing arrow there is a hook to which the fishing line is attached. The other end of the fishing line is tied into the crossbow itself.

Did you find an error in the text? Select it, press Ctrl + Enter and we'll fix it!

Entertainment like this homemade crossbow made of wood is interesting for both adults and children. True, for the latter, entertainment is not safe, and therefore they need to play only under the supervision of adults. It is not difficult to make such a crossbow, and it will shoot with ordinary iron plugs.

materials

To do wooden crossbow with your own hands, prepare:

• wood bars;
• bandage cord;
• glue for wood;
• self-tapping screws;
• wooden dowel;
• ice cream sticks;
• pencil;
• iron corks from bottles;
• hacksaw or saw;
• jigsaw;
• sandpaper;
• drill;
• drill.

Step 1. The first step is to make a bow for a crossbow. To do this, take a wood strip 0.64 cm thick with parameters 1.9 x 30.5 cm. The source material is a deciduous tree, in this case it was poplar. Soak the strip in water overnight and then press it with clamps to the round flat surface, leaving the workpiece in this form until completely dry.

Step 2. In the rounded strip, you need to drill three holes. Two on the sides should be 0.3 cm. The size of the hole in the center is 0.6 cm.

Step 3. Secure the strip in this form with a bandage cord.

Step 4. Send a wooden block into the bow of the crossbow and secure it with wood glue and a self-tapping screw.

Step 5. Pull the bandage cord to the maximum and at this point mark with a pencil on the central bar of the product.

Step 6. In the place marked with a mark, make a notch.

Step 7. Drill a hole in the notch and send the dowel into it. lower part cut and process the bar, giving it the look of a real weapon.

Step 8. Now you have to make a latch and a trigger. To do this, use strong ice cream sticks. From the sticks make two parts shown in the photo. For the trigger, you just need to cut off one of the rounded ends, and for the latch, cut off the third part and glue the three cut strips in a stack from the bottom. In length, they should reach the middle of the latch.

To make a homemade crossbow you will need:
* A bar of non-resinous wood species, size 700x10x40 mm.
* The second sheet of the spring of the car Moskvich.
* Profile pipe 50x50x2 mm. 10 cm long.
* Profile pipe 15x15x1.5 mm.
* A small piece of sheet metal 2 mm.
*Metal stainless steel 4 mm thick. and 0.5-1 mm. (for the descender).
* Corner steel 50x50x4 mm. 35 cm long.
* Bar D=8 mm. 40 cm long.
* Bolts with nuts D=8
* Stainless steel molding from the door VAZ-2106 2 pcs.
*Metal rollers 2 pcs., glass lifting mechanism from the door of a VAZ car.
* Rope D=3 mm. 3 m long, two terminal loops.
* Epoxy resin, wood stain, wood varnish for outdoor use.
*Two small springs (working in tension).
* A dozen nails for roofing felt, one nail two hundred, tube D = 6 mm., Small washers.

We will use the following tools:
*Welding machine.
*Saw circular manual.
* Electric drill with speed control, carbide drills for metal D=3, 5, 8, 10 mm.
*Bulgarian, cutting discs for metal, grinding discs for wood.
*Keys, pliers, screwdriver, vise, narrow chisel, knife.
*File, sandpaper.
* Goggles.

Item 1. Making a bed.

Let's take a well-dried wooden block, I had a birch, sketch a bed on it. We make the size of the butt each for ourselves (for our height), and the bed, depending on the length of the arrows that you will use. I use 440 mm arrows, but I had to save money on the butt, I left only 300 mm, the total length turned out to be 740 mm, I didn’t risk doing it anymore.

Let's draw a markup for the selection of the guide, for the plumage of the arrow, width 5 mm, depth 10 mm.

Using a circular saw, we cut out the groove for the entire length, to the end of the trigger (lock).

It should look like this.

Using a drill D=12 mm. choose a cavity descender, we level the ledges with a chisel and a knife. We drill a hole for the trigger, bore it with a chisel and a knife.

Point 2. Making a lock or trigger.

For the basis of the lock we take the type "nut". So that nothing rusts, we will use stainless steel, take a sheet 4-5 mm thick, if you can’t find one, make a typesetting of several sheets glued together and riveted. We draw the shape of the details on the metal.

Using a cutting disc and a grinder, we cut out according to the marking of the workpiece.

In the center of the "nut" we drill a hole for the axis of rotation D = 6 mm.

We process all sides with a file.

We grind with sandpaper, achieving a completely smooth surface.

It should turn out something like this.

We grind the rest of the elements of the castle, sear.

I lengthen the trigger with two thin sheets of stainless steel, fix it with homemade rivets.

On the grinding machine we achieve the desired shape of the blanks.

From a thin sheet of metal we make the body of the trigger mechanism.

We drill three holes D = 2.5 mm in the body of the sear, one for the mounting axis and two for mounting the springs.

Attach the trigger spring in place.

Let's see how the parts become in the cocked state on the table.

And as after the shot.

We attach one side of the case to the inside of the mechanism and drill holes for all the axles in place.

From a two-hundred nail, 6 mm in diameter, we will make an axis for the "nut".

Saw off the sharp end of the nail.

We measure the length of the future axis, saw off.

From thin nails for roofing material, we will make the rest of the rivet axles. We will remove the ebbs on the nail heads with a grinder.

Now they fit well to the body.

Install the sear on the axis in the body, use the intermediate washers.

Saw off the excess length of the nail, leaving 1 mm. on both sides for rolling.

Using an anvil, hammer the end of the axle with a hammer.

We drill a hole for the axle with a spacer, for fastening the spring sear.

From a suitable tube, cut off the spacer sleeve on this axis.

Move to one side of the body.

We install the axle, bushing and hook the spring.

Assemble the body halves together.

We saw off the excess length, leaving a protrusion of 1 mm. under the hammer

Let's roll.

Now you can put the largest axis-rivet of the castle. Align the holes.

Let's take the previously measured and sawn off axis D = 6 mm., Immediately tap a little with a hammer on one side.

We install in place.

And we will also roll, the main thing is not to overdo it, so as not to pinch the movable mechanism inside.

Point 3. Installing the lock mechanism in the box.

If something prevents the castle from sitting well in place, we refine it with a chisel or knife. After installation, we check how the trigger goes.

If everything is fine, you can drill holes for the mounting screws and screw them into place.

Now we need decorations from the VAZ-2006 door, they are also made of stainless steel, which is very good. To give them additional rigidity, epoxy resin was poured inside.

After complete hardening, in a day, we will drill four holes D = 3 mm in each, for fixing screws.

With a large drill, we will make hiding places for the heads of the screws so that the bowstring cable does not catch when it slides along it.

We polish the exits of the holes with fine sandpaper to remove all the burrs that damage the cable.

We install the finished guides on the bed.

We make sure that the screws do not go through in thin places.

We check that the lock goes without hooks on the guides.

Item 5. Making an arc or shoulders.

From the same donor doors, we extract with the help of a grinder, the rollers of the glass lifting mechanism.

Of these, we will make blocks for the shoulders, and the arc itself from the second leaf of the spring, an old Moskvich car.

Let's make blocks, for fastening of a spring to a bed.
To do this, from a corner of 50x50 mm. we cut out the constituent elements to assemble by welding, here is such a mount (block).

We will process the welds with a grinder. Drill mounting holes D=10 mm. under the bolts.

According to the finished sample and the dimensions of the resulting block, we make grooves for fastening in the box. We try on the fit, achieve a tight entry and fastening. According to the calculated position of the future bowstring, we outline and make a through groove in the sidewall of the bed, 70 mm long. 10 mm wide, lower bowstrings will go here.

We bend and weld the leg brace (stirrup).

Ears for blocks.
From a profile pipe 50x50 we will make lugs for attaching roller blocks to the arc (spring).

The most difficult thing in making the arc itself from the spring at home is to drill holes in it. It is necessary to drill with a drill at low speeds so that the drill does not burn, constantly apply water. If possible, drill with drills of different diameters, from thin to thick in increments of 0.5-1 mm., constantly sharpen the tool.

We fasten the brackets to short M8 bolts, grind off the hats.

We fasten the spring to the block with two M8 bolts, followed by a small welding along the edge of the fastening.

Now you need to open the bed with varnish and dry.
We install a block with an arc on the bed, upset with a hammer for a tight fit of metal-wood.

We insert and tighten the bolts on M8.

From long M10 bolts we will make axle bolts reduced in length with a short thread for blocks.

We take a tube from the anchor and make spacers for the axes of the blocks out of it.

Let's drill holes D = 10 mm in the ears. to install blocks. Install rigid loop ends on the cable.

We install a block with a cable on one side of the shoulder. Do not overtighten the nut so as not to pinch the rotation of the roller.

We drill a hole for the stud in the nut and bolt.

Install the stud and tighten it with a nut in the direction of unscrewing.

We push the cable through the hole in the bed and do the same with installing the roller on the other side of the shoulder.

Item 6. Top part castle.

From a profile pipe 15x15 mm. saw off two segments of 120 mm. We cut out two (L) shaped blanks from sheet metal with a grinder, one rectangular plate (on top) and a triangle (on the back).

By welding we connect all the parts together, we clean the welding seams with a grinding disc to get a kind of one-piece part.

From an old folding steel meter, we make an elastic arrow holder.

The photo shows the bolts for mounting the rail under the optical sight.

The same thing, only the bolts also clamp the boom holder at the same time.

The sight rail itself (dovetail) is made of the same 2 mm sheet metal, with the sides ground off for mounting the optics.

A square lining is visible along the optics rail to raise the back and thereby tilt the sight down, for proper aiming at a target beyond 25 m.

We install the lock bracket on the bed and drill holes for fastening, self-tapping screws and an M6 bolt.

We twist small self-tapping screws so that they do not go into the channel of the plumage of the arrow.

We twist the back screw.

In addition, we drill a hole and install the last bolt.

Installing an optical sight.

Are you interested in medieval culture? Do you want to get a fashionable accessory, impress your friends with an exclusive souvenir? Decided to make an unusual gift close person? Then you can easily make a magnificent crossbow right at home! Exactly this species sports weapons are now rapidly gaining popularity, and people are happy to purchase them for themselves as a souvenir, a catchy design element. Why do you need a bow, what to do with it? Here are just a few of the most common ways to use a crossbow.

• An excellent solution is to use a crossbow on shooting ranges. Here is what an archery lover says: “You can arrange marksmanship competitions with friends, shoot at targets with pleasure, organize role-playing games. A bow will always come in handy for such a hobby, it will allow you to develop attentiveness, the ability to concentrate, and respond quickly.”
• Nowadays, crossbows are increasingly used for hunting. It is enough to load an arrow into such a bow and shoot accurately to become the happy owner of a partridge, a hare.
• Crossbows are also in demand as sporting weapons. There are professional athletes who regularly take part in competitions and constantly train. They also often make bows with their own hands.
• The bow can be made the central detail of the interior. Designers note its versatility: “The crossbow looks amazing in any room. In the corridor, he has a particularly formidable look, meeting everyone who enters the house. In the hall, he emphasizes the solemnity, focuses on the character of the hosts. In the bedroom, the bow hints at a passionate relationship, the power of love. In the kitchen, a crossbow might well be hung next to a hunting painting of game.”
• Increasingly, people are acquiring, making crossbows with their own hands to please their acquaintances, friends, colleagues with an unusual gift. Such a souvenir will be surprisingly original, will definitely come in handy and will evoke vivid emotions. It is especially appropriate to present a present to a man.

Now that you know how useful an onion is, how it can be used in many ways, it's time to familiarize yourself with the basic principles of its manufacture. How to make a crossbow at home, what you need to know so that it looks good, shoots well, can become a worthy weapon, souvenir and accessory? We'll find out very soon. The algorithm will help you, useful recommendations.

We make a crossbow with our own hands

You will need a good selection of wood. You can not take conifers, too old, dry branches. The crossbow consists of three main elements. It is necessary to make a high-quality trigger, stock and arc. Act strictly according to the algorithm, do not confuse the steps. You will succeed!

• You need to make an arc. It is advisable to take yew, hazel or ash for her. The board should be flat, without slant and knots. Make a thickness of about 2 cm. A piece of wood must be dried, kept for several days, and then cut evenly. The length of the arc is approximately 75 cm, the width can be made about 4 cm, the arc should gradually become thinner towards the edges. Thickness from the edges - 1.5 cm.
• Now you need to make a bed. For it, you will need hardwood, which is quite hard. Take a board of such a size and shape that it is convenient to hold it in your hands. Remember that from one edge you need to make a special groove where the arc will be inserted.
• It's time to machine the groove for the arc. You need to make a hole for fastening from a rope at a distance of ten centimeters from the cut groove for the arc. Now insert the arc into the groove, and then fix it there with a rope. Now attach the bowstring to the ends of the arc using the cuts made for this. Stretch the string as you would while shooting. It is necessary to designate a point that is as far away as possible. Now determine the optimal size of the crossbow - it should be equal to your forearm in length.
• A responsible task is the manufacture of the trigger for your bow. Previously, pin type locks were made. You will have to familiarize yourself with hallmarks such a mechanism. When you have already made a mark at the place of the maximum tension of the bowstring, you need to drill a hole through there. A transverse recess must be made in the box, in its upper part. Then fix the lever at the bottom of the crossbow. Most often, the axis is made of wood, and attached with wire.
• Now the bed and the lever must be folded together. Fasten the elements with a rope. The lever should move on the axis with minimal friction.
• Now you need to make a small pin, thanks to which the bowstring will be pushed out of the bow. The pin should be round, it is better to make it from oak. The pin will pass into the recess of the lock freely, without getting stuck due to the fastening. When the lever is raised, the plane of the bed and its upper edge should be equal. It is the pin that will push the bowstring.
• For the arrow, you will need to make a special chute. The recess extends from the top opening of the lock to the leading edge. The gutter must be laid at a shallow depth, approximately like a quarter of an arrow.
• Then it's time to work on the details. All elements must be walked with sandpaper. Sometimes parts are covered with egg white, after dissolving it in water.
• Secure the arc in the groove using a strong rope. See if the lock works well. All elements must be finally adjusted so that the mechanism is as strong as possible.